• John Deere Power Flow Bagger Manual Transfer Switch
• John Deere Power Flow Bagger Manual Instructions
• John Deere Power Flow Bagger Installation
• John Deere Power Flow Bagger Manual Craftsman
• John Deere Power Flow Bagger 48c Installation
• John Deere Power Flow Bagger Manual

Installing

Park Machine Safely

1. Stop machine on a level surface, not on a slope.

• John Deere Manuals. Power Flow Operator's Manual for 48 and 54 inch Mowers, Serial # 010,001. JD Rear Bagger and Power Flow 7-Bushel Operator's Manual fits All GX.
• 48C, 54C, 62C Power Flow (Export) English: Operators Manual CD-ROM: OMM156391CD: 44 Inch Front Blade: English: Operators Manual CD-ROM: OMM151683CD: 44-Inch Snowblowers Compatible w/X300 & X500 Series Tractors North American Edition (000) English: Operators Manual CD-ROM: OMM154285CD: 7 Bu Rear Bagger: English: Operators Manual CD-ROM.

2. Disengage Power Take-Off (PTO).

3. Lower attachments to the ground.

4. Lock the park brake.

For LX280 (Not LX280 AWS) and LX289. Requires appropriate rear bagger chute or blower assembly and Power Flow chute. MCS Power Flow blowers: BM22696 48C/48X high-performance blower assembly for mowers with rotating anti-scalp wheels (X300/X500 M-T/X700). Requires BM21681 Power Flow chute. 7 product ratings - John Deere M71340 Power Flow Fan Rotor 38' 46' 48' 50' 54' Rear Bagger Mower. Removing Power Flow™ Storing POWER FLOW™ Section 35 - Operating Using the Blower Assembly Unplugging Mower, Bagger, or Material Collection System Section 40 - Service Removing Drive Belt Installing Drive Belt Section 45 - Troubleshooting Using Troubleshooting Chart Section 50 - Getting Quality Service Service Literature Parts John Deere.

5. Stop the engine.

6. Remove the key.

7. Wait for engine and all moving parts to stop before you leave the operator's seat.

8. Close fuel shut-off valve, if your machine is equipped.

Install Ballast

Install front ballast. (See Install Proper Ballast in PREPARING VEHICLE section.)

Install Hopper Assembly

GX, SX, RX, and SRX Series Riding Mowers

M96589

1. Slide hopper H-frame (A) into mounting bracket (B).

2. Align holes in mounting bracket with top holes in H-frame. Insert pin (C) through holes and secure with spring locking pin (D).

STX Series Lawn Tractors

NOTE: For easier installation, always secure receiver frame to tractor before installing H-frame.

M96619

1. Hang receiver frame (A) onto stud (B) at both sides of rear frame.

2. Install clevis pin (C) through hole in hitch plate. Secure with spring locking pin (D).

3. From inside of rear frame, install clevis pin (E). Secure with spring locking pin (F). Repeat at opposite side of tractor.

4. Place H-frame (G) through receiver and secure with pins (H) at both sides.

LT Series Lawn Tractors

NOTE: For easier installation, always secure receiver frame to tractor before installing H-frame.

M96591

1. Hang receiver frame (A) onto stud (B) at both sides of rear frame.

2. From inside of rear frame, install clevis pin (C). Secure with spring locking pin (D). Repeat at opposite side of tractor.

3. Place H-frame through receiver frame and secure with pins (E) and (F) at both sides.

Spin-Steer Lawn Tractors

MX7615

Picture Note: Bagger pin can be installed from either side.

1. Slide hopper support frame (A) between stop bracket and mounting bracket (B).

2. Align holes in mounting bracket with holes in support frame. Install bagger pin (C) through holes and secure with spring locking pin (D).

MX7615

3. Check that support frame fits tightly between stop bracket and mounting bracket, and that bagger pin can be removed easily. Adjust bolts (E) if necessary.

LX Series Lawn Tractors With 2-Wheel Steer

NOTE: For easier installation, always secure receiver frame to tractor before installing H-frame.

M96612a

1. Pin receiver frame to rear tractor frame with rods (A). Secure with washers (B) and spring locking pins (C).

2. Place H-frame through receiver and secure with bagger pin (D) and spring locking pin (E).

LX Series Lawn Tractors With All-Wheel Steer

NOTE: For easier installation, always secure receiver frame to tractor before installing H-frame.

MX1545

1. Attach receiver frame to the frame adapter bracket:

· Hook receiver frame slotted adapter plates onto the frame adapter bracket.

· Align holes in receiver frame with holes in frame adapter bracket. Insert retaining rod (A) through holes.

· Install flat washer (B) onto rod end and secure with spring locking pin (C).

MX1546

2. Place H-frame through receiver and secure with bagger pin (D) and spring locking pin (E).

GT and 300 Series Lawn and Garden Tractors

NOTE: For easier installation, always secure receiver frame to tractor before installing H-frame.

M96661a

1. Position receiver frame onto stud (A) at both sides of tractor.

2. From inside of rear frame, install clevis pins (B). Secure with washers (C) and spring locking pins (D).

3. Install clevis pin (E) through hole in hitch plate. Secure with spring locking pin (F).

4. Place H-frame through receiver opening. Install bagger pin (G) and secure with spring locking pin (H).

400 Series Lawn and Garden Tractors

M96518

1. Pull outward and rotate to lockout J-pin (A) at both sides of H-frame (B).

NOTE: On early model 400 Series tractors, H-frame welded pin is inserted into center hole (C).

John Deere Power Flow Bagger Manual Transfer Switch

M96515 M96517

2. Insert H-frame welded pin (D) into outer hole in hitch plate.

MX1551

3. On tractors with 3-point hitch, both hitch pins (E) should be captured between U-bracket weldments on bagger frame

M96516

4. Align hole in outer bracket (F) with hole in mounting strap (G). Lock J-pin into holes. Repeat for other J-pin.

Install Cut-N-Throw Bagger Chute (7-Bushel Rear Bagger System Only)

30 and 38-Inch Mower Decks

M96602

1. Insert round end of bagger chute (A) into upper chute (B) at hopper assembly.

MX1542

2. Lift up discharge chute at mower deck and fit bagger chute opening over mower deck discharge chute. Make sure discharge chute is properly hooked at back side of discharge opening (C).

M70256

3. Place retaining strap (D) over tab (E).

4. Slide adjusting hardware (F) against tab (E). Adjust hardware, if necessary, to secure the attachment.

5. Secure rubber strap hook (G) through hole in tab (E).

42C Mower Decks

M96602

1. Insert round end of bagger chute (A) into upper chute (B) at hopper assembly.

MX1541

2. Lift up discharge shield (C) and deflector (D).

MX2907 MX2906

3. Fit chute (E) over discharge opening. Make sure lower edge of chute is seated completely in lip (F).

4. Place slot in retaining bracket (G) over tab on mower deck. Secure front hook (H) through hole in tab.

5. Secure rear hook (I) through hole in mower deck lip.

42 All Purpose Mower Decks (For Spin-Steer Only)

NOTE: For easier installation, lower the mower deck cutting height to 51 mm (2 in.) or less.

M96602

1. Insert round end of bagger chute (A) into upper chute (B) at hopper assembly.

MX1541

2. Lift up discharge shield (C) and deflector (D).

MX7618

3. Put anchoring rod (E) through opening under discharge deflector as shown and fit chute over discharge opening. Make sure tab (F) is positioned inside hinge bracket slot (G).

MX7619

4. Hook anchoring rod (E) behind hinge bracket (H) on top of discharge shield.

MX7620

5. Check that lower edge of chute is seated completely in lip (I). It may be necessary to clean debris from lip.

6. Secure two chute hooks (J) through hooks on mower deck.

Install Power Flow Chute (7-Bushel Power Flow System Only)

M96602

1. Insert round end of power flow chute (A) into upper chute (B) at hopper assembly.

2. If necessary, hold open exhaust door on blower assembly. Slide square end of power flow chute over blower outlet.

MX1543 M57646 M75353a

Picture Note: Top photo - 38QT and 48QT Power Flow, middle photo - 38 and 46 - Inch Power Flow, bottom photo - 48 and 54 - Inch Power Flow.

3. Secure strap hook (C) through metal loop (D).

Those who own or have come across a John Deere EZtrak mower understand they are incredibly simple to operate while also getting the job done right each time. However, the mowing process can be enhanced even further thanks to a number of available zero turn mower attachments. From bumper attachments to mower lights, there are a range of options to choose from when it comes to making the landscaping experience even better.

To showcase some of these attachments, we’ve put together a list that provides a short description of each. Enjoy!

1. The 15-Gallon Sprayer

Utilize this 15-gallon sprayer attachment to apply a variety of liquids, including liquid fertilizer, weed killer, tree spray, de-icer and more. The sprayer’s boom sprays a 60-in. swath and a 19-foot hose and wand have the ability to spot spray lawns and shrubs. Available for Z400s and Z600s.

2. Dual Headlight Kit

For lawn enthusiasts that mow early in the morning or later in the evening, the dual light kit is available, focusing light in several directions to brighten the mowing area. This attachment is compatible with Z425, Z445, Z465, and Z655 EZtrak mowers.

3. Floor Mat

The EZtrak floor mat sports a stylish Deere logo and protects the foot deck with a non-slip, washable material. The mat is resistant to chemicals that may get on it during landscaping jobs. The mat is compatible with Z225, Z245, Z400s, Z600s, Z235, and Z255 models.

4. Deck Front Roller Kit

The front roller kit attaches to the front of the mower deck to help prevent scalping of the lawn and improve the smoothness of the job. The roller kit is available on Z425 and Z445 mowers (48-in. and 54-in. decks).

5. The 6.5-Bushel Hopper and Chute Assembly

The hopper design provides landscapers with an effective solution for collecting grass clippings and leaves (Z235 and Z255). There is also an available assembly with the Power Flow system (Z425, Z445, Z645, and Z655).

6. Grass Groomer – Lawn Striping Kit

There aren’t many better things to lay your eyes on than a freshly mowed lawn with a neat striping pattern. The lawn striping kit is built with flexibility, durability, and non-weight bearing design, making it an effective tool for pattern mowing. The kit is available on the Z225, Z235, Z245, Z425, Z445, and Z465 mowers.

7. Foot Rest Extensions

Operators sometimes spend a lot of time on their EZtrak mowers. With this in mind, Deere has made bolt-on footrest extensions available on Z400 and Z600 mowers to make mowing an even more comfortable experience.

8. Rear Bumper

Accidents happen. With the John Deere EZtrak rear bumper attachment, accident damage to the back of the mower can be reduced. The bumper bolts on to Z400 and Z600 tubular frames for solid support.

9. Rear Hitch

Available for Z400 and Z600 mowers, the rear hitch bolts securely on to the tubular frame, providing a solid amount of towing capability. The rear bagger bracket is included with all rear hitches.

10. Utility Cart

Want to haul any number of materials with your EZtrak mower? No problem. The rust and dent-resistant poly cart comes in a 7 and 10 cubic foot option that are both easy to dump, resulting in complete emptying.

11. Foot Lift Kit

The foot lift kit allows EZtrak mower operators to easily raise or lower the mower deck without having to use their hands. This attachment is great for quickly raising or lowering the deck when unexpected obstacles like tree roots or rocks appear in the mowing path. This kit is available on the Z235, Z255, Z425, Z445, and Z465 mowers.

John Deere Power Flow Bagger Manual Instructions

John Deere Power Flow Bagger Installation

12. Lawn Sweeper

The John Deere lawn mower sweeper attachment has the capacity to hold 17 bushels of material and includes a brush-height adjuster with eight positions. Available on all EZtrak series mowers.

John Deere Power Flow Bagger Manual Craftsman

As spring rolls into summer, there will be plenty of time spent outdoors manicuring the lawn. We hope this list inspires John Deere EZtrak mower owners (or potential owners) to add even more capability to their equipment.

John Deere Power Flow Bagger 48c Installation

If you have any questions about John Deere lawn care equipment, you can contact your local John Deere dealer.

John Deere Power Flow Bagger Manual

If you enjoyed this post or want to read others, feel free to connect with us on Facebook, Pinterest, or Twitter!